| Cheshire Cat Computing http://www.steveshipway.org/forum/ |
|
| Routers cgi and multiple interfaces http://www.steveshipway.org/forum/viewtopic.php?f=2&t=373 |
Page 1 of 1 |
| Author: | mrrlg [ Tue Sep 21, 2004 5:01 am ] |
| Post subject: | Routers cgi and multiple interfaces |
| Author: | stevesh [ Tue Sep 21, 2004 1:59 pm ] |
| Post subject: | |
| Author: | mrrlg [ Wed Sep 22, 2004 1:32 am ] |
| Post subject: | |
Here are the "error" messages from cfgmaker for the marked out interfaces. ###Interface 4 >> Descr: 'T1-0/1' | Name: 'T1 0/1' | Ip: '' | Eth: '' ###The following interface is commented out because: ### * it is a DS1 controllers ### * got 'Received SNMP response with error code ### error status: noSuchName ### index 1 (OID: 1.3.6.1.2.1.2.2.1.10.4) ### SNMPv1_Session (remote host: "172.18.1.20" [172.18.1.20].161) ### community: "public" ### request ID: -1752370354 ### PDU bufsize: 8000 bytes ### timeout: 2s ### retries: 5 ### backoff: 1)' from interface when trying to query ### Interface 5 >> Descr: 'T1-0/2' | Name: 'T1 0/2' | Ip: '' | Eth: '' ### ### The following interface is commented out because: ### * it is a DS1 controllers ### * got 'Received SNMP response with error code ### error status: noSuchName ### index 1 (OID: 1.3.6.1.2.1.2.2.1.10.5) ### SNMPv1_Session (remote host: "172.18.1.20" [172.18.1.20].161) ### community: "public" ### request ID: -1752370353 ### PDU bufsize: 8000 bytes ### timeout: 2s ### retries: 5 ### backoff: 1)' from interface when trying to query ### Interface 6 >> Descr: 'Serial0/1:0' | Name: 'Se0/1:0' | Ip: '172.19.2.24' | Eth: '' ### ###Target[172.18.1.20_Se0_1_0]: #Se0/1:0:public@172.18.1.20: ###SetEnv[172.18.1.20_Se0_1_0]: MRTG_INT_IP="172.19.2.24" ###MRTG_INT_DESCR="Serial0/1:0" ###MaxBytes[172.18.1.20_Se0_1_0]: 192000 ###Title[172.18.1.20_Se0_1_0]: #Se0/1:0 -- 2650main ###PageTop[172.18.1.20_Se0_1_0]: <H1>#Se0/1:0 -- 2650main</H1> ### Interface 7 >> Descr: 'Serial0/2:0' | Name: 'Se0/2:0' | Ip: '172.21.2.24' | Eth: '' ### ###Target[172.18.1.20_Se0_2_0]: #Se0/2:0:public@172.18.1.20: ###SetEnv[172.18.1.20_Se0_2_0]: MRTG_INT_IP="172.21.2.24" ###MRTG_INT_DESCR="Serial0/2:0" ###MaxBytes[172.18.1.20_Se0_2_0]: 192000 ###Title[172.18.1.20_Se0_2_0]: #Se0/2:0 -- 2650main ###PageTop[172.18.1.20_Se0_2_0]: <H1>#Se0/2:0 -- 2650main</H1> As you can see, MRTG is reporting a Maxbyte count on each of the marked out interfaces. It has to do with how it reads Interface 4 and 5. Any ideas? |
|
| Author: | mrrlg [ Fri Feb 11, 2005 3:13 am ] |
| Post subject: | routers cgi and multiple interfaces |
You will need to look at the configuration of your cisco router. Depending on what you are routing with the vwic-smft card, T1's or voice, the names of the interfaces and OID's will be different. After all, you are terminating two interfaces in a single slot on the 2600 series chassis. |
|
| Page 1 of 1 | All times are UTC + 12 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|